Auto Solar Panel Laminator

1.Auto solar panel laminator 2.PlC+Touch-screen control systerm 3.All parameters are setup on the touch-screen

ZHUHAI BAIXIN MACHINERY CO.,LTD. is one of the biggest manufacturers and exporters of the solar module line equipments in mainland China.Singapore,India,Indonesia,Malaysia,Phillippines,Bangladesh,Jordan,Cuba,Argentina,USA,Australia,UK,Italy,

Spain,Sweden,POLAND,GERMANY,Croatia,Austria,Nigeria,etc.

Solar Panel Laminator

(1) PLC+TOUCHED LCD controlled auto solar module laminator. Laminating area size: 2700*2100mm. Capacity:7.5MW

(2) Heating system includes 1 unit PID controller, 1 pcs heating steel plate with size:3000*2400*58mm, oil tubes, heat transfer oil, oil heating station with safetycertificate. Max working pemperature:180 degree C, we suggest: workingtemperature range,120~150 degree C, at this range, temperature uniformity ±1.5°C, temperature control accuracy ±1 °C ( after amending)

(3) Special transfer system, modules can be transferred to the laminatingarea frame by frame. This will cause less movement and broken. Broken less than0.1%.

(4) Cooling fan at the output area can cool the laminated solar moduleswith fresh air. This will match the product line especially the sun simulatorfor testing the solar module with temperature range 0~80 degree C ( THE SUNSIMULATOR CAN EMEND AND CALCULATE AUTO MATICALLY to the data as at temperature25 degree C )

(5) It has password for the operator, through this password, all theparameters including: tank temperature, heating plate temperature, vacuum time,lower chamber air charging time, 1st laminating time, 2st laminatingtime etc, can be set on the touched LCD. And the cycle can be countedautomatically. Both the setting data and the real data can be shown on thescreen. It will cause less broken for laminating in two times not in one time.

(6) Alarm system:

A: It will “NOTICE” if the real temperatureis not more than 120 degree when you want to start the laminating and will alarm if the temperatureis not more than 120 degree when it is laminating.

B: It will alarm if if the real temperatureis 10 degree C higher than setting.

C: It will alarm if the vacuum inside thelower chamber can not reach the setting data in 2 minutes when vacuum the lowerchamber.

D: It will alarm 1 minute before opening thecover , in this one minute, you may press “ PAUSE”. This is for placing thesolar module onto the correct area.

E: There is one oil level gauge in the OILHEATING STATION. It will alarm if the level is lower than setting , check ifany oil leakage , then add oil, it will not alarm.

(7) Maintenance Notice

A:It will shown on the screen , you should change the HEAT TRANSFER OIL ( 1 year1 time, model: Mobil Termia 603 )

B: Itwill shown on the screen for you to change the SILICON MEMBRANE and the siliconslat ( 1 pcs every 1500 cycles) .

C: It will shown on the screen for you tochange the VACUUM PUMP OIL ( every 1500 hours)

(8) With 1 pcs Rotary vacuum pumps(model: 2X70) , vacuum speed: 70L/S, real vacuum can be 30~50Pa.

(9) Safety design

A Cover closing alarm. With one unit of light protecting system and wallprotecting system, it will alarm and stop the cover closing if some one goinside the setting area when the cover is closing.

B Oil tubes between the heating plate and the oil station, are packagedby special cloth to prevent the hurt.

C The two cylinders for cover opening and closing are lockable, even thepower shut down or pressure air shut off, the cover will not come downsuddenly.

D There is EME cover opening system. When the laminating is going on, thecover can be opened even the power is shut off.

E The machine foot is special designed to prevent earth quake.

(10) Power supply, 380Vac/50Hz,60KW. Ever age power cost, about 35KW.

(11) Pressure air supply, 0.7~0.9MPa. Speed, 0.4~0.8 M3/Minnute

(12) Dimension

A Main body: 980CM(L) ,290CM (W),195CM (H)

B Heating Station: 165 CM (L), 60CM (W) ,160CM(H)

C Vacuum station: 130 CM(L),90 CM(W),150CM(H)

(13) Weight: total,13T , Laminating part, 9 T

(14) Power supply, 380VAC, 50 Hz, 50Kw, 3 phases 5 wires. Workingpower 28~32 KW

Auto Solar Panel Laminator